What space, power and plumbing does a self-service drink machine need?
Most site surveys fail on details that nobody wrote down: the door cannot open because a shelf is 40 mm too close, or the circuit is shared with a chest freezer that trips at 3 a.m.
This page lists what an unmanned fresh-beverage machine physically demands, in the order a site survey should check it. Figures below describe the DOZZON U1-PLUS class of machine (670 mm wide, 1790 mm high, 868 mm deep); always confirm against the model you are ordering.
Short answer. about 2 m² of floor, one 220–240 V single-phase circuit, and no mains plumbing if you choose a tank-fed model. A 670 mm wide cabinet needs roughly 900 mm of clear width for door swing and cup access, and about 15 minutes a day for refilling.
1. Footprint and clearances
The cabinet itself occupies 0.58 m². What matters more is the working envelope around it.
Plan for 900 mm of clear width in front of the cup outlet so a person can stand square to the screen, and 100 mm behind the unit for ventilation. If the machine sits against a wall on one side, leave 60 mm so the side panel can be removed for service.
- Cabinet footprint: 670 × 868 mm (0.58 m²)
- Recommended bay: 900 mm wide × 1000 mm deep
- Service access: 600 mm in front, 60 mm on one side
- Headroom: 2000 mm minimum for filter and hopper access from above
2. Electrical supply
A single-phase 220–240 V circuit is enough. Do not share it with refrigeration or HVAC: a compressor starting on the same leg will dip the voltage and can fault the brewer mid-cup.
Fit an RCD (residual current device) and a dedicated isolator within reach. Machines with heated water tanks draw their peak during heat-up, not during dispensing, so size the breaker for the warm-up load.
- Voltage: 220–240 V, 50/60 Hz, single phase
- Circuit: dedicated, with RCD and local isolator
- Socket: within 1.5 m of the cabinet, not behind it
- Earthing: required; do not rely on the water pipe
3. Water: tank-fed versus plumbed
Two configurations exist and they change the site survey completely.
Tank-fed machines carry an internal reservoir that you refill by hand or from a food-grade jerry can. No plumber, no drain, and the machine can be moved between locations.
Plumbed machines take a 1/4-inch or 3/8-inch supply with a pressure regulator and a shut-off valve, plus a drain or a waste tray that is emptied daily.
For offices, gyms and event spaces, tank-fed is usually the right answer: it removes the single most expensive part of an installation.
4. Drainage and waste
Every machine produces waste: drip tray overflow, cleaning water, and in some designs spent grounds or capsules. A tank-fed unit collects this in a tray or a small waste bin that an operator empties on the daily refill round.
If you plumb the machine, fit a trap and an air gap. Direct connection without an air gap is a backflow risk and, in most jurisdictions, a code violation.
5. Network and payment
Remote monitoring and cashless payment both need connectivity. A 4G router inside the cabinet is the simplest option; office Wi-Fi works if the signal reaches the location and the network does not use a captive portal.
Allow outbound HTTPS on port 443. Machines that must reach a payment terminal also need a stable low-latency link; test it before signing the lease, not after.
6. Floor and environment
A loaded machine weighs several hundred kilograms. On a raised floor or a mezzanine, confirm the point load with the building manager before delivery.
Keep the unit out of direct sun and away from ovens, fryers and dishwashers. Ambient above 32 °C forces the refrigeration to work continuously and shortens its life; below 5 °C most recipes need recalibration.
Site requirements by location type
| Location | Bay needed | Power | Water | Daily task |
|---|---|---|---|---|
| Office pantry | 900 × 1000 mm | 220 V dedicated | Tank-fed | Refill + empty tray, 15 min |
| Retail frontage | 900 × 1000 mm | 220 V dedicated | Plumbed preferred | Refill only, 15 min |
| Factory floor | 1000 × 1100 mm | 220 V, surge protection | Plumbed | Refill + filter check |
| Event / pop-up | 900 × 1000 mm | 220 V, 16 A | Tank-fed | Refill per session |
Related
- Coffee machine specifications
- Deployment scenarios and site planning
- Certifications needed for EU and US import
FAQ
Can the machine run on 110 V?
Export versions are built for the destination market. 110–120 V models exist for North America and Japan; confirm the voltage at the time of order, because the heater and pump are matched to it and cannot be swapped in the field.
Does it need a water line and a drain?
Not necessarily. Tank-fed models need neither. Plumbed models need a regulated supply and a drain with an air gap. Choose tank-fed when plumbing work would delay the installation.
How much space in front of the cup outlet?
Plan 600 mm of clear floor in front of the outlet so a person can stand square to the machine. The cup shelf projects 160 mm from the front panel and the cup sits at 700 mm above floor level.
What internet connection does it need?
Any connection that allows outbound HTTPS. A 4G router inside the cabinet is the most reliable option; guest Wi-Fi with a captive portal will not work without re-authentication.
Can it be moved after installation?
Yes, on its casters over a flat surface, after draining the tank and the boiler. For anything involving stairs or a vehicle, use a pallet truck and secure the cabinet.